Buck Hollow Sporting Goods - click or touch to visit their website Midwest Habitat Company

Blazers vs. Quick Spins

Monsterbuck

Active Member
I was preparing to refletch some arrows and wasn't sure which vanes I wanted to use, I've read a lot of good things about both the Bohning Blazer and NAP Quick Spin vanes. I had Bohning send me a sample of the Blazers and I bought a small package of Quick Spins. I used a new set of IW arrow wraps and fletched three arrows with each type of vane.

I decided to do my testing at 30 yards because a lot of the shots on deer I get are around that range and I figured it would give me a better indication of how the vanes affected flight than 20 yards would.

I decided to begin by shooting a few rounds with my field points to see how well they flew and grouped and then switch to broadheads to see how the flight characteristics changed.

I began by shooting the three Blazer equipped arrows.
1111BLAZER.jpg


These grouped well with field points at 30 yards.

Then I shot a group with the three Quick Spins.
1111QUICKSPIN.jpg


They also grouped well and right in with the Blazers and where my regular arrows had been grouping. (The low arrow was a slight dip in my bow arm that I realized as I released).

I decided to try shooting all six arrows into the target next to see if they still grouped together. MISTAKE! As I fired the third arrow I heard a different sound on impact but shrugged it off. I shot the other three and went to check out my grouping.
1111CENTERED.jpg


Well my testing was now down to only two Blazer fletched arrows as the Quick Spin centered the shaft of one of them.

I decided to shoot no more than three at a time and both vanes continued to group well. After about 30 to 40 shots with each brand I replaced the field points with Muzzy 3-blade broadheads exuipped with practice points.

The Muzzy tipped arrows with Blazer vanes continued to hit right where they had been with field points, grouping well. The Quick Spin fletched arrows still grouped fairly well but consistently hit 3 to four inches lower. I'm not sure what to attribute this too. Any difference in weight did not effect the flight with field points. I shot at least another 30 to 40 shots with each brand vane and the results were consistent, the Blazers grouping right with my field points and the Quick Spins consistently shooting low.

Now I don't claim to have any real scientific evidence based on my own personal testing of these two brands of vanes that one is definitely better than the other. I can only say that with my own set-up the Blazer vanes performed better with the broadheads I intend to hunt with than the Quick Spin vanes and any arrows I re-fletch from now on will carry them.
 
Re: Blazers vs. Quick Spins *DELETED*

I too have tested the blazers with muzzy 100 gr three blade practice blades. With the blazers the broad head flight was very similar to a field point. Last year, with much effort, I could not get the muzzy broad heads to group like my field point. I think Blazers for fixed blades are making good sense.
 
Ive heard that the quickspins take some speed off of your arrow, this could be why you were grouping low with them.
 
I don't have any explanation but they definitely grouped with my other arrows with field points and were definitely 3 to 4 inches lower with broadheads. I have not tried them at various ranges, just at 30 yards. I'll have to try them at 20 and 40 and see how they fly. I'm just offering my experience in one shooting situation.
 
If the Quick Spins are slowing down your arrows, shouldn't they be calling them "Slow Spins"????
grin.gif
 
I have a sample of blazers on the way, but my experience in the past is that muzzys shoot lower than my field points. They just do. I shoot 100 gain muzzys and am going to try some blazers. In the past, I would adjust my sights and everything was fine. I just got tired of moving my sights around.
 
The extra rotation causes more drag in the air, reducing your forward speed of your arrow, at least thats how I understood it. The whole reason for more spin was to gain tighter groups, which I dont think is noticable enough to even bother using them when you could just use the blazers.
 
I am using the 4" QS and they did tighten the group a little and the weight did make my groups lower, but that was an easy fix.
 
Ok, but weight, spin and drag didn't affect them with my field points, only when I put the broadheads on.

I don't want to have to move my sights around either. I want to be able to practice with my field points during the week and hunt with my broadheads on the weekend and not have to move my sight around each time. That's why I'll stick with the Blazers on the arrows I re-fletch. The fact that they're a lot cheaper is a bonus.
laugh.gif
 
Monsterbuck -

I can do that with my bow. Not just because it is a Hoyt. Just kidding. Alot of it has to do with the alignment of your nock. Try giving them a little twist to get them all to hit the same spot. It takes a little time, but it is worth it.

I shoot 72 pounds, 550 grain arrow, 4 inch feathers, 125 grain fixed head steel force serrated broadhead. It is important to make sure your arrows all weight the same, cut to the same length, nocks are all in the exact same spot. Be sure to paper tune your bow also with the exact arrows that you are going to be flinging. Remember, we are not machines, so hitting that same spot each time isn't the easiest thing in the world to repeat. Make sure you take the weather into consideration also.

Quick Spins - My opinion on them is they drastically increase the rotation (RPM's) of the arrow, creating a turbine effect with your arrow. Higher RPM = more penatration/cutting. Just my opinion on them.

One last thing. The larger the Feather/Vane, the faster your arrow will stabilize during flight.

I do this, and my broadheads hit exactly where my field points do. Like I said, it takes a little time, but it is worth it in the end.

Stop over and see Brady at Central Archery. He is a whiz at tuning. Or shoot me a PM and I'll meet you over there.

Good Luck
 
could it be that your broadhead and your vanes aren't alined right? try heating the head until the glue softens, and give it a little twist
 
Top Bottom